Beginner’s Guide to Leatherworking – ManMadeDIY

Angst aside, I was right, I could. And you could too.    

The first thing you’ll do is cut out the pieces for your project. And this is something that’s pretty easy, but there’s a right way to cut and a not-so-right way. Because cutting out the leather is generally the first step in making a leather item and your cuts affect the difficulty of the steps that follow. Clean cuts ensure that burnishing is easy and your stitching lines are straight. Getting a clean cut is all about scoring, using a ruler that won’t slip and having a sharp knife.

First, trace out your project onto the leather using a scratch awl and ruler.

Next, cut out each piece with a knife and a heavier ruler that isn’t going to slip. There are a lot of different kinds of knives that work well when cutting leather. If you are just getting into leatherworking, rotary cutters work well.

Gluing will keep your edges pressed together while you prepare the leather for stitching. You’ve been doing this one since first grade, so there’s not a whole lot to learn here. Applying the glue is not hard, but there are some ways that can improve how well the glue holds like sanding the area you’re gluing, making sure you glue only where you need with wax paper, and apply pressure when the glue is drying.

First, sand the area that you are planning on gluing, especially if it’s on the flesh side (surface or top side) of the leather. This will make it so the glue can sink into the leather a bit and adhere much better.

Next, lay down some wax paper and apply the glue with a paintbrush. Getting glue in the wrong spot is a serious pain to try and clean up, so use wax paper to keep the glue where it needs to be.

Finally, apply pressure while it dries. Often I will use binder clips, but make sure the leather you’re using for your project doesn’t get dented by the blinder clips. If that’s the case, just lay a cloth over the edge and then clip on the binder clips.

This is probably the hardest skill to learn out of them all, but still pretty easy to pick up. Stitching a leather project together is a multi-step process. It involves marking out your stitching lines, punching your stitching holes, and finally saddle stitching the item together. Saddle stitching is a hand stitch that is widely used in leatherworking due to its durability, and learning it isn’t that hard. Check out these five simple steps to learn how to saddle stitch.

First, mark your stitching lines with a divider. If you’re not sure how far to set your stitching in, a general rule of thumb is to have the distance between the stitching and the edge be the same as the thickness of the edge.

Next, punch your stitching holes using a diamond chisel. The only trick to this is to make sure that your chisel is perfectly perpendicular to the leather. A slight angle one way or the other will make it so the stitching on the backside doesn’t line up. This is especially a problem on thicker projects, like belts.

Now to the hard part: saddle stitching. Once you have the needles through the first hole, take the needle on the left side and push it through the leather. Then, with the right needle, come behind the left needle to make a cross.

Next, with the right needle still behind the left needle, pull the left needle through and rotate your hand toward you so that the left needle is now facing you and the right needle is facing the stitching holes.

Finally, put the right needle through the same hole you just pulled the left needle through. If you used a diamond chisel, each hole will be a diamond shape. This means that each hole has a high point and a low point. For your stitching to look uniform you need to consistently put the right needle back through the hole at the same point in the diamond, ideally the point of the diamond that is closest to you. Once the needle is through, pull both tight. At that point, you’ve finished your first saddle stitch. On to the next one. Once you’ve completed your entire stitching line, you’ll need to backstitch. Back stitching is a saddle stitch that goes backwards two to three holes to make sure the thread won’t come lose.

If you’re trying to learn to stitch, it is ultimately a little bit hard to read how to do it. It’s just something you have to see. If you’re still having trouble understanding how to stitch (and I would be) you can check out this stitching guide, which also has a quick video to show you how to stitch.

Once your project is stitched together, making sure to finish your edges will give your project a professional look. There are multiple ways to edge finish, the three main ways being: burnishing, edge painting, and edge turning. Burnishing is probably the easiest and yields some great results. This process finishes the edges by melting the loose fibers together with heat created through friction. Basically, that just means you rub the edges with a piece of canvas until it looks good. A simple burnishing process includes: beveling edges, sanding them, dying them, burnishing them with a piece of canvas cloth, and then finishing the edge with beeswax.

First you’ll need to bevel your edges. The reason for this is that the surface of the leather will start to fold over as you sand the edge. Beveling basically removes that part that would fold over. Beveling is super easy. All you need to do is run the beveler along the edge with a moderate amount of force.

Next, you’ll need to get the edges nice and smooth. Generally, I hit it with a couple of grits of sandpaper. First, start with a 200 grit sandpaper, this will even out any part of the edge that is not flat with the rest. Then, sand off loose fibers with a 600 grit sandpaper.

Once the edges are smoothed out, it’s time to dye the edge. I apply the dye with a wool dauber. But, dying the edge isn’t something you have to do. If you want your edge to be a natural color, then don’t dye it. Typically though, I will dye the edge with the same color I used to dye the surface. When you burnish the edges will naturally darken, so using the same dye provides a darker shade of the same color, which always looks good.

After the edges have been dyed, it’s time to actually burnish. To do this, dip your finger in water and lightly wet the edges. Make sure not to soak the edges though. Leather becomes very pliable when soaked and can be molded. This is great for other things, but not so much when your burnishing. Once you’ve put water on the edges, rub a canvas cloth across it briskly until the edges start to darken and shine. You’ll know you’re done when you start to hear a tacky sound.

And finally, apply some beeswax to the edge. This helps keep the leather water-resistant and makes the edges look dang good. After putting on the beeswax, make sure to buff the edges again with a piece of canvas. Then you’re done.